A dedicated forum and online store for the Opae ula shrimp! 

■ Our Opae ula shrimp web store is now open! We are selling Opae ula Shrimp and Macroalgae via our eBay store HERE
Share photos/videos, journals and logs for your Opae ula tank setups for others to read.
 #4445  by QDanT
 11 Feb 2018 11:19
Hi opae ula related I'm no scientist unless 'mad scientist' counts :smile:
back in the dark ages before computers I had a black and white dark room and used to photograph Diatoms with the microscopes develop the film then print the photo's but as we came into the didgital age the chemicals for black and white became harder and harder to get so I gave over and now just make up slides of Foraminifer and shells from beach sand http://www.fernwood-nursery.co.uk/sand/danny.htm
15mm circle
shelhi.JPG (12.25 KiB) Viewed 632 times
 #4446  by opae ula related
 11 Feb 2018 17:23
well you need to photograph opae ula larvae etc..... :lol:
 #4489  by QDanT
 14 Feb 2018 21:06
my light and bulb arrived
Light.jpg (67.43 KiB) Viewed 466 times
stays cool to the touch so set it on the tank lid cut from,a food safe, plastic storage box lid
tank lid 2.jpg
tank lid 2.jpg (75.46 KiB) Viewed 466 times
light set up.jpg
light set up.jpg (130.98 KiB) Viewed 466 times
I've taken the foam filter out and replaced it with a fine air stone, and moved the heater to horizontal at the back. The light's on a timer with a 12hrs cycle
light timer.jpg
light timer.jpg (73.74 KiB) Viewed 466 times
next is to make a box to hide the Rats nest of wires
I've a TDS meter from when I made Colloidal silver the LFS RO water reads 002 ppm (the house water 70ppm) I bought an hygrometer so 2.5gm Tropic Marin sea salt in 1ltr RO water gave SG 1.003, put one of my Marrimo moss balls in, seems to like it so I'll put the other in and slowly raise the SG
moss balls.jpg
moss balls.jpg (114.71 KiB) Viewed 466 times
meters.jpg (138.25 KiB) Viewed 466 times
next is to add salt to the tank and play with the test kit
test kit.jpg
test kit.jpg (45.46 KiB) Viewed 466 times
not shure when to add the 'quick start' ?
 #4490  by odin
 14 Feb 2018 21:07
As soon as you have water and salt mixed get adding the quick start :grinning:
 #4491  by QDanT
 14 Feb 2018 22:18
I was going to add the marine salt premixed with RO water to fill the tank
does the quick start Bacteria need food i.e. Ammonia to start the cycle, few drops then test
though I cann't find a small amount of pure Ammonia, how about Spirulina let it decay watch for Ammonia spike the Nitrite then hopefully
Ammonia 0 Nitrite 0 Nitrate ? (low)
 #4492  by odin
 14 Feb 2018 22:41
Either way will be fine, mixing before hand will make the salt dissolve quicker, if you add the salt direct to the tank with water and rocks in already it can lay on the sand in a sort of mat or get in between the rocks and take longer to dissolve.

You can get the cycle going but you will have to keep feeding it, I’d personally just set it up and get the tank temp up to 22deg C or slightly higher... dump in the QuickStart and get the lights on to grow some algae and leave it at that for a few weeks.

Sent from my iPhone using Tapatalk Pro
 #4493  by QDanT
 14 Feb 2018 22:52
OK Dumb question if the RO water's so 'pure' where's the Algae going to appear from ? is there anywhere to get some as a starter ?
 #4502  by odin
 15 Feb 2018 18:09
i assume from spores or dirt that falls in the tank, it does need a food source but the crap in your substrate and rocks will no doubt kick things off.
 #4505  by QDanT
 16 Feb 2018 17:43
with 195gm of Tropic Marin salt added the tanks at SG 1012 and a steady 72*F so added 5ml of Quick Start.
I've some Ammonium Chloride in the post, after some of thats in (5.25ml) I'll start the Ammonia and Nitrite testing.
Getting there :happy:
01.jpg (82.81 KiB) Viewed 440 times
 #4509  by QDanT
 19 Feb 2018 15:47
Just been given a piece of Coral, brought it to boil in RO water gave it a good scrub, dried it out on the stove top then soaked overnight in SG 1.012 water and added it to the tank, that should be the PH buffer sorted ?
03.jpg (166.62 KiB) Viewed 388 times
04.jpg (67.63 KiB) Viewed 388 times
Added x10 drops of Ammonium Chloride to the tank, gave it a couple of hours, then did an API Ammonia test reading :- 2ppm will check tomorrow and see if it's dropping
  • 1
  • 2
  • 3
  • 4
  • 5
  • 14